GLI GLI Quality Tool
GLI Quality Tool — Version 2.0

Training TB Laboratory Staff to Use a Biological Safety Cabinet

Safe sample processing depends on more than switching on a biological safety cabinet (BSC). Staff must understand airflow, work practices, personal protective equipment, decontamination and the limits of the cabinet before they handle sputum or other potentially infectious tuberculosis specimens.

A practical training program should combine explanation, demonstration, supervised practice and documented competency assessment. This approach suits Australian laboratories ranging from large metropolitan services in Sydney and Melbourne to small regional facilities supporting remote communities, where staffing, maintenance access and specimen transport may be very different.

Define The Safety Purpose

A Class II BSC is designed to protect personnel, the surrounding environment and the work from aerosols generated during procedures such as opening containers, pipetting, vortexing or preparing samples for microscopy and culture. It does not make an unsafe procedure safe, and it does not replace respiratory risk assessment, good laboratory technique or appropriate personal protective equipment.

Trainers should explain that a BSC is different from a chemical fume cupboard. Its filtered airflow and front opening are designed for biological work, while volatile toxic chemicals may damage filters or create a separate exposure risk. Staff should also know that a BSC cannot compensate for blocked grilles, excessive movement, open doors, poor siting or overloaded work surfaces.

Training stage Staff capability Evidence of competence
Explain Describe cabinet purpose, airflow and limitations Short discussion or knowledge check
Demonstrate Perform start-up, loading and shutdown correctly Trainer observation
Practise Process a simulated specimen using controlled movements Completed observation checklist
Verify Respond to spills, alarms and equipment faults Scenario-based assessment
Maintain Record cleaning, certification and incidents Accurate quality records

The training should be linked to the laboratory’s quality management system. The GLI Quality Tool’s GLI Quality Tool downloads can support a structured approach to documentation, personnel competency, equipment management and continual improvement.

Prepare The Room And Cabinet

Before a session, inspect the cabinet’s location and confirm that it has current certification from a qualified service provider. Air-conditioning outlets, doors, busy walkways and high-traffic benches can disturb the inflow curtain. A cabinet positioned beside a frequently used passage may be technically functional yet difficult to use safely.

Show staff where the certification label, operating instructions, electrical isolation point, spill kit and waste containers are located. Explain what each alarm means and establish a clear rule: an alarm, unusual airflow, damaged sash, failed light or uncertain cabinet status means work stops until the issue is assessed.

Australian laboratories should align the procedure with applicable state or territory Work Health and Safety requirements. The model Work Health and Safety Act 2011 applies in many jurisdictions, while Victoria uses the Occupational Health and Safety Act 2004. Local risk assessments, institutional policies and NATA requirements should determine the final procedure rather than relying on a generic poster.

Teach A Consistent Workflow

Staff should begin by removing unnecessary items, disinfecting the work surface with a product and contact time approved by the laboratory, and allowing the cabinet to run for the period specified by the manufacturer or local procedure. They should check that grilles are unobstructed and position materials so clean items enter before potentially contaminated items.

The working area should be divided into clean, dirty and waste zones, with the cleanest materials furthest from the operator and contaminated materials moving in one direction. Staff should avoid placing large items against the back grille, covering the front grille or repeatedly reaching across open containers. Slow, deliberate movements help preserve the air curtain.

Demonstrate how to open specimen containers gradually, keep tubes low within the work zone and pause after actions that may generate aerosols. Vortexing, vigorous mixing and centrifugation require specific controls. If centrifugation is needed, sealed safety cups or rotors should be loaded and opened according to the laboratory’s validated procedure, ideally within the BSC where appropriate.

Practise PPE And Behaviour

PPE should be selected through a task-based risk assessment. A typical workflow may include a buttoned gown or protective coat, gloves and eye or face protection where splash risk exists. Respiratory protection requires a separate assessment; fit-tested P2 or equivalent respirators may be necessary for particular TB procedures or risk profiles. Facial hair, spectacles and correct donning technique need to be addressed without assuming that a mask alone controls exposure.

Training should include hand hygiene, glove changes and the prohibition on touching phones, pens, door handles or personal items while gloved. Australian staff often move between benches during a busy shift or take short breaks around rostered meal periods, so trainers should rehearse how to stop work, remove PPE safely and wash hands before leaving the laboratory.

Use a harmless simulation material, such as coloured water or an approved surrogate, to make contamination visible. Ask each learner to identify a deliberate error, such as placing a waste bag over a grille or reaching from the dirty zone into the clean zone. This turns abstract advice into observable technique.

Manage Spills And Equipment Problems

Every operator should know the immediate response to a spill inside the cabinet. The procedure should cover stopping work, keeping the cabinet running if safe to do so, allowing aerosols to settle where required by the risk assessment, applying disinfectant from the outside toward the centre and observing the validated contact time. Broken glass must never be picked up by hand.

A spill outside the cabinet, a dropped specimen, a leaking container or a splash to the face requires a separate response. Staff need clear instructions for leaving the area, notifying the supervisor, accessing first aid and reporting a possible exposure. The laboratory should maintain incident records and review them for system weaknesses rather than treating each event as individual carelessness.

Cabinet failure, power interruption and alarm activation should be practised as short scenarios. Operators must know when to secure specimens, close containers, restrict access and contact engineering or the certified service provider. They should never bypass an alarm or continue processing because a batch is urgent.

Build Competency Into Quality Records

Reading a procedure is insufficient evidence of competence. A trainer should observe each employee completing start-up checks, loading, simulated sample manipulation, waste handling, surface disinfection and shutdown. The assessment should record specific behaviours, not simply state that the person “understands” BSC use.

Refresher training is appropriate after a prolonged absence, a cabinet relocation, a significant procedural change, an incident or repeated non-conformities. New staff should work under direct supervision until they meet the laboratory’s acceptance criteria. Experienced scientists also benefit from periodic observation because shortcuts can develop during busy periods.

Keep training records with the employee’s competency file, including the date, assessor, cabinet identification, procedure version, scenarios used and any corrective action. A simple trend review can show whether errors cluster around night shifts, temporary staff, specimen surges or particular equipment.

Connect Cabinet Practice With Contamination Control

Good BSC technique protects staff and helps preserve the validity of TB results. Contamination can arise from poor separation of clean and dirty materials, incorrect disinfection, splash events, faulty centrifuge handling or movement that disrupts airflow. Supervisors should review contamination investigations alongside cabinet observations rather than looking only at culture results.

When contamination rates change, trainers can use a practical contamination troubleshooting guide to structure the investigation. The review should consider specimen reception, transport delays, media, equipment, cleaning records, staff technique and environmental conditions.

This is especially relevant across Australia, where specimens may travel long distances from regional or remote services before reaching a central laboratory. Heat during transport, courier schedules, weekend delays and limited access to replacement consumables can affect both specimen quality and workflow pressure. In larger cities, high throughput and crowded shifts create different risks, including rushed cabinet loading and frequent interruptions.

Recommendations For A Sustainable Program

A sustainable program also needs realistic resourcing. Laboratories should check the local market for reliable supplies of certified filters, disinfectants, sealed centrifuge accessories, gowns and gloves rather than assuming rapid replacement is available. Remote sites may need contingency stock and a service agreement that accounts for travel time, while metropolitan laboratories may need planned maintenance windows that do not disrupt high-volume work.

The supervisor should make expectations visible through a concise work instruction near the cabinet, supported by a full procedure in the document-control system. Short toolbox sessions can revisit one skill at a time, such as clean-to-dirty workflow or response to a power failure, without removing staff from the bench for a full day.

Use the BSC competency checklist in the next training cycle, observe each operator with a simulated TB workflow and record corrective actions in the laboratory quality system. This turns safe cabinet use from a one-off induction topic into a measurable part of routine patient and worker protection.