GLI GLI Quality Tool
GLI Quality Tool — Version 2.0

Implementing Temperature Mapping for TB Storage and Incubators

Reliable temperature control is essential in tuberculosis laboratories. Refrigerators, freezers, specimen storage areas and incubators can show substantial variation between shelves, corners and door zones, even when a single built-in display appears normal. A temperature mapping study reveals those differences and provides evidence that critical materials are stored within approved limits.

For Australian laboratories, the study should fit the laboratory’s quality management system, local work health and safety requirements and the expectations of accreditation. The GLI Quality Tool provides a practical framework for laboratories building quality systems in different resource settings, including facilities that manage TB testing, culture and related storage processes.

Define The Purpose And Scope

Begin by identifying every storage location where temperature could affect a TB laboratory process. This may include specimen refrigerators, reagent fridges, freezers, culture incubators, warming cabinets and rooms used for temporary storage. Include equipment used for media, quality-control materials, molecular reagents and clinical specimens where applicable.

The scope should state the equipment identification number, location, capacity, normal set point, acceptable operating range and materials stored inside. It should also identify whether the study will be performed empty, normally loaded or under a deliberately challenging load. A refrigerator used for reagents may require different assessment from an incubator holding culture media, so each use should have a documented rationale.

Use the manufacturer’s instructions, validated test methods, reagent specifications and laboratory procedures to establish acceptance criteria. A refrigerator may be required to remain between 2 °C and 8 °C, while an incubator may have a narrower target around a validated culture temperature. Do not choose limits simply because they are convenient or displayed on a nearby thermometer.

Australia’s climate makes the scope especially important. A laboratory in Darwin may experience high outdoor temperatures and heavy air-conditioning demand, while a facility in Hobart may face cold rooms and seasonal heating changes. Mapping should represent the conditions that create the greatest risk, rather than relying only on a mild day in spring.

Select Instruments And Prepare The Study

Use calibrated temperature data loggers with a suitable range, resolution, accuracy and recording interval. Their calibration certificates should be current, traceable to recognised standards and linked to unique instrument numbers. A data logger that is appropriate for a warehouse may not provide adequate accuracy for a 35 °C incubator.

Before placement, check the loggers against a reference instrument or perform the laboratory’s approved pre-use verification. Record the logger ID, calibration due date, battery status, date and time synchronisation. If a logger clock is wrong by several hours, the results may be difficult to compare with door-opening records, alarms or power interruptions.

Prepare a map of the equipment and mark the planned positions. In a refrigerator, include upper, middle and lower shelves, corners, the centre, areas near the door, and locations close to the cooling outlet. In an incubator, cover the working volume rather than only the centre. The number of loggers should be justified by the size, shape and risk of the chamber.

Before starting, remove unnecessary items and ensure that stored materials will not obstruct air circulation. Do not place loggers directly against walls, shelves or cooling plates unless that position is being deliberately assessed. A label on the door or a study worksheet should identify that mapping is in progress, preventing staff from moving loggers accidentally.

Capture Normal And Challenging Conditions

Run the study long enough to show repeated temperature cycles and recovery after normal access. The exact duration should be defined in the protocol, but several days is often more informative than a short spot check. The study should include the equipment’s routine operating pattern, including compressor cycling, defrost cycles and typical loading.

For an incubator, record the time needed to recover after the door is opened and after a normal tray or rack is inserted. For a storage refrigerator, observe the effect of routine stock access, cleaning, replenishment and removal of materials. If staff routinely open a door many times during a morning shift, the study should represent that behaviour.

Consider a separate challenge under the most credible adverse condition. Examples include a fuller load, a near-empty chamber, a warmer season, overnight air-conditioning reduction or a simulated power interruption. Any challenge must be risk-assessed and controlled so that specimens, cultures and valuable reagents are not placed at risk.

Australian buildings can create distinct patterns. Energy-saving practices may reduce air-conditioning overnight, and facilities may operate with different settings during weekends or public holidays. A laboratory in Sydney, Melbourne or Brisbane may also experience temperature changes when external doors remain open during deliveries. These routine events should be included if they can affect the storage area.

Analyse The Results And Identify Risk

Download the data without altering the original files and retain the raw records with the approved report. For each logger, review minimum, maximum and average readings, time outside limits, rate of change and recovery after disturbances. Graphs are useful because they show whether a brief excursion occurred at one location or whether the whole chamber drifted.

Identify the warmest and coldest points, often called hot spots and cold spots. A refrigerator may have a warm zone near the front or door and a cold zone close to the evaporator. An incubator may show gradients between the top and bottom shelves. The result should distinguish true equipment variation from a logger that was moved, touched, exposed to condensation or affected by a low battery.

Compare the findings with predefined acceptance criteria. A small brief excursion may have a different impact from a persistent deviation, but the decision must be based on documented risk assessment. Consider the sensitivity of the stored material, duration of exposure, uncertainty of measurement and whether the material can be released for use.

When a result fails, quarantine affected materials where appropriate and follow the laboratory’s deviation procedure. Investigate possible causes such as overloading, blocked vents, damaged door seals, poor probe placement, incorrect set point, unstable power supply or inadequate maintenance. Do not simply repeat the study until a favourable graph appears.

Convert Findings Into Controls

The report should include the protocol, equipment details, environmental conditions, logger certificates, placement diagram, raw files, graphs, calculations, acceptance decision and authorisation. A second reviewer should check that the data are complete and that the conclusion matches the evidence. Records should be controlled under the laboratory’s document and record-management procedures.

Corrective action may involve redistributing stock, reducing the load, changing shelf assignments, adjusting the set point, repairing seals, servicing the compressor or relocating the unit away from heat sources. In an incubator, it may be necessary to restrict certain shelves or add a validated circulation system. Any change that could affect performance should be followed by verification or remapping.

Temperature monitoring should continue after the study. Install a routine maximum-minimum thermometer or continuous monitoring system where justified, with alarm limits based on the validated operating range. Define who reviews alarms, how quickly staff respond, where excursion records are stored and how affected materials are assessed.

Australian laboratories should also consider work health and safety duties under the applicable state or territory legislation. Handling dry ice, refrigerants, electrical equipment, heavy freezer loads and biological materials may require separate controls. Australia’s laboratory market includes local calibration providers, equipment service companies and monitoring suppliers, but certificates and service claims should be checked rather than accepted at face value.

Review The Study Through The Quality System

Temperature mapping is stronger when it is connected to the laboratory’s wider quality activities. Link the study to equipment management, purchasing, facilities, document control, incident management, internal audit and continual improvement. The quality management guidance can help place the work within a structured system rather than treating it as an isolated engineering exercise.

Set a review interval based on risk and equipment history. Remapping may be required after relocation, major repair, replacement of a controller, changes in capacity, repeated alarms, significant building work or a major change in room climate. A fixed annual schedule may be appropriate for some equipment, while stable low-risk units may follow a different documented interval.

Include temperature mapping in staff training and competency assessment. Staff should know which shelves are approved for particular materials, how to respond to an alarm, how to avoid blocking air circulation and how to document stock movement during an excursion. Everyday habits, such as leaving a refrigerator door open while checking several boxes, can undermine a well-designed control system.

Use trends to improve the system. Repeated warm readings near a door may support a change in workflow, while gradual drift across months may indicate developing equipment failure. Phase-specific improvement resources, including the Phase 4 guidance, can support laboratories as they review evidence, address recurring problems and sustain improvements.

Start with a controlled protocol, calibrated instruments and a clear map of every critical storage space. Complete the study under representative conditions, investigate every deviation and retain the evidence in the quality system. This approach gives TB laboratory staff a defensible basis for protecting specimens, reagents and cultures while strengthening readiness for internal review, external assessment and accreditation.