GLI GLI Quality Tool
GLI Quality Tool — Version 2.0

TB lab continuous temperature monitoring log replacement

Manual thermometer records depend on staff completing morning and evening rounds and transcribing readings. They create blind spots when a refrigerator, incubator, water bath or heated block drifts outside its accepted range. A continuous temperature monitoring log replaces point readings with a time-stamped electronic trail, allowing deviations to be detected and acted on while specimens or cultures can still be protected.

Replacing manual thermometer records is a quality-system change, not a device purchase. Define what must be monitored, who reviews records, what triggers an excursion alarm, and how affected material is handled. The GLI Quality Tool’s four-phase roadmap and twelve Quality Systems Essentials provide a framework for assigning duties across safety, personnel, equipment, documentation, assessment and continual improvement.

Australian conditions shape the design. Metro laboratories in Sydney, Melbourne, Brisbane and Perth share engineering, security and after-hours rosters, while regional facilities may depend on couriers, flights and intermittent connectivity. Hot summers, cold snaps and power interruptions affect sensor placement, backup power and alert escalation. The system must serve regional facilities as well as central laboratories.

The benefits are stronger traceability, earlier action and a defensible account of specimen acceptability. Digital monitoring also creates duties around calibration, data integrity, access control, retention and privacy. Stage implementation so paper records are not discarded before the electronic system, staff response and corrective-action workflow have been validated.

Map the risks and define the scope

Begin with a risk inventory of temperature-sensitive TB laboratory activities, including specimen receipt and storage, reagents, heat blocks, water baths and incubators where local procedures require monitoring. Confirm limits from manufacturer instructions, specimen acceptance criteria, validated methods and accreditation requirements. Do not assume one threshold applies to every item or incubator.

Map the existing process from reading to review: how values are taken, transcribed, signed, escalated and retained; where gaps occur overnight, on weekends and public holidays; and who can reach equipment after hours. Record missed readings, ambiguous corrections and unresolved excursions. This shows whether the main risk is instability, poor visibility, delayed response or unreliable documentation.

Use the quality system checklists to structure the gap assessment and assign evidence to relevant Quality Systems Essentials. Give the implementation lead, quality representative, biosafety contact, engineering contact and clinical liaison defined responsibilities. Record approval in change control, including equipment, software settings, training and validation.

Select equipment for Australian conditions

Choose a digital data logger suited to the monitored range and Australia’s local supplier market. Assess sensor accuracy, calibration status, logging interval, memory, clock accuracy, alarm outputs, battery life and data export. Local suppliers and NATA-accredited calibration providers can support procurement, but each device needs fit-for-purpose verification and a defined calibration interval. Remote sites may need local storage and scheduled synchronisation.

Install probes away from direct cooling airflow, doors, heating pipes and cleaning zones while retaining a representative view of the monitored item. In busy Sydney and Melbourne hospital laboratories, coordinate access with engineers, cleaners and couriers; in regional facilities, protect equipment from dust, heat and transport damage. Use power or battery alerts where an outage could threaten samples, and test notifications after hours.

Before withdrawing manual checks, run the new system beside the existing process for a defined trial. A logger can improve coverage, but it cannot determine whether affected material remains acceptable after an excursion. Keep manual checks available during verification, then retire them through an approved change rather than leaving disconnected systems running.

Control Manual thermometer record Continuous temperature monitoring log
Monitoring coverage Readings only at scheduled rounds Time-stamped data at a defined interval
Traceability Depends on initials and accurate transcription Preserves logger identity, time, value and alerts
Excursion detection Often noticed on the next round Threshold alerts can identify deviations promptly
Investigation Requires recalling earlier readings Trends and exported history support impact assessment
Routine workload Repeated readings and ruling lines Setup plus review of exceptions; physical checks remain
Main limitations Gaps, omissions and disputed corrections Calibration, power, connectivity, clock drift and alarm fatigue

Build the electronic record into the quality system

The electronic record should show logger and sensor identity, monitored location or equipment, sample or batch reference where appropriate, timestamp, temperature, alarm state and action taken. Define how staff download, review, sign off and export records, and check system clocks. Preserve an audit trail for edits; never overwrite an original reading that appears wrong.

The standard operating procedure should specify monitoring intervals, alarm thresholds, excursion limits, acknowledgement time, investigation steps, escalation contacts, corrective action, calibration, maintenance, backup and retention. Cover logger failure, connectivity loss and a manual fallback. Distinguish a monitoring data gap from a genuine temperature excursion.

Protect linked information under the Privacy Act 1988 where applicable and under applicable state or territory privacy laws, especially when a log is tied to a patient specimen. Use role-based access, secure exports and defined retention rather than placing names beside readings in an open spreadsheet. Physical changes must preserve safe waste segregation; the laboratory waste sorting guide can support a clear adjacent procedure for documenting those controls.

Train staff and protect the handover

Training should be practical and role-specific. Staff must distinguish a warning, critical excursion, device fault and communication outage. Demonstrate probe placement, logger checks, alarm acknowledgement, escalation and the approved fallback. Observe competency during supervised shifts rather than inferring it from attendance.

Practical competencies to verify

Embed the workflow in familiar Australian routines: the morning laboratory huddle, shift handover, after-hours on-call escalation and engineering rounds. Replace the old rounding sheet with a dashboard review focused on open alerts, overdue checks and logger faults. Route exceptions through the laboratory’s phone, pager or secure messaging chain rather than informal personal messages.

Handover details that should travel with every shift

Managers should compare alarm acknowledgement and closure times with the SOP’s limits. Repeated nuisance alarms call for threshold review; ignored alarms call for retraining. Record training completion, competency results and alarm-routing changes in personnel and documentation files, then check them during internal quality audits.

Validate the system and manage excursions

Validate the configuration before go-live through risk-based temperature mapping and comparison of each logger with a calibrated reference under representative conditions. Confirm that displayed values, exported values and alert triggers agree, and document the accepted tolerance. Test continuity during power loss, internet failure, clock drift and logger restart. Verification confirms intended operation; calibration controls measurement accuracy over time.

Define a closed-loop excursion process: acknowledge the alert, confirm the reading, protect affected material, assess time and magnitude, consult the relevant SOP and document the release or rejection decision. Where patient care may be affected, use a laboratory communication protocol to specify who contacts the treating team, what is reported and how uncertainty is explained. Cross-reference the communication and investigation records.

Review performance at a frequency proportional to risk. Useful measures include expected data received, missing intervals, alarm acknowledgement time, unresolved excursions, calibration status and corrective actions closed within target. Trend results by site and device rather than one laboratory average. Feed recurring causes into risk assessment, preventive action, training and maintenance schedules so the log supports continual improvement.

Roll out the change and sustain oversight

Roll out in phases: pilot one critical storage area, compare data with manual checks, train the full roster, correct gaps, and only then extend the system. Preserve the old paper archive according to the approved retention schedule, and record when each legacy thermometer sheet was superseded. Expansion should follow the same change-control and validation process used at pilot sites.

Check the arrangement against applicable state or territory Work Health and Safety laws, Safe Work Australia guidance, electrical safety controls and site biosafety approvals. Consider the Biosecurity Act 2015 and BICON requirements when regulated biological material enters or leaves Australia. Where accreditation applies, map evidence to NATA expectations and ISO 15189. These frameworks support, rather than replace, the local risk assessment.

Start by naming the laboratory manager and quality lead, selecting one high-risk location, and documenting required fields, thresholds, alarm recipients and the fallback process. Download the relevant GLI Quality Tool checklist, gather logger and calibration information, and schedule a supervised trial. A successful rollout ends when every missing interval, alarm and corrective action has an owner and a defensible record.