GLI GLI Quality Tool
GLI Quality Tool — Version 2.0

Creating a TB Laboratory Safety Data Sheet Binder

A well-organised safety data sheet (SDS) binder gives tuberculosis laboratory staff immediate access to the chemical information they need for safe storage, handling, spill response and disposal. It should cover every substance in use, from sodium hypochlorite and ethanol to Ziehl–Neelsen stains, solvents, acids, fixatives and gases.

The binder is most useful when it forms part of the laboratory’s quality management system rather than sitting separately from daily work. Its contents should connect with chemical inventories, risk assessments, induction records, emergency procedures, waste arrangements and equipment maintenance.

Australian laboratories must also account for local work health and safety requirements. The model Work Health and Safety framework, Safe Work Australia guidance and state or territory regulators provide a strong baseline, but laboratories in New South Wales, Victoria, Queensland, Western Australia and other jurisdictions should check the rules applying to their site.

Define The Binder’s Purpose And Scope

Start by writing a short purpose statement inside the front cover. State that the binder contains current SDS documents for all hazardous chemicals and other substances used, stored or produced by the TB laboratory. Explain who must use it, where the electronic copy is held, who maintains it and what to do if a required SDS cannot be found.

Set the scope broadly enough to capture materials that are sometimes overlooked. Include cleaning products, stains, buffers, culture reagents, controls, disinfectants, compressed gases, liquid nitrogen, oils, maintenance chemicals and chemicals held in small quantities. A reagent used once a month still needs an SDS if it remains on site.

List the rooms and work areas covered by the system, such as specimen reception, the microbiology room, media preparation area, stores, autoclave room and waste holding area. In a multi-site service, identify whether the binder applies to one laboratory in Sydney, a regional facility near Cairns or the entire health network.

Build A Complete Chemical Inventory

The inventory is the foundation of the binder. Record the product name, manufacturer, supplier, catalogue or product code, concentration, pack size, quantity held, storage location and responsible area. Add the date received, expiry date where relevant and the date the SDS was obtained or checked.

Use the manufacturer’s exact product name rather than a local nickname. “Bleach” may refer to different sodium hypochlorite concentrations, while “alcohol” could mean ethanol, isopropanol or a blended disinfectant. Record working solutions as well as concentrated products when their hazards differ or staff prepare them routinely.

Compare the inventory with purchase records, stores shelves, refrigerators and benches. Include chemicals ordered through Australian laboratory suppliers and products bought locally from industrial, medical or hardware channels. A quarterly stocktake can reveal unrecorded bottles, duplicate names and substances that have been discontinued.

Obtain Current Australian SDS Documents

Request the SDS from the manufacturer or Australian supplier, and retain the version supplied for the product actually held. Australian SDS documents should use the Globally Harmonized System classification adopted for workplace chemicals. Check that the document identifies the supplier, hazard classification, ingredients, first aid measures, fire response, accidental release controls, handling, storage and disposal information.

SDS documents should generally be reviewed at least every five years under Australian requirements, and sooner when the manufacturer issues an update, the product changes or new hazard information becomes available. Put the issue date and next review date into the inventory rather than relying on someone to notice an old document in a crowded folder.

Avoid replacing an old SDS simply because a newer document is easier to download. Confirm that the newer version matches the same formulation, concentration and product code. If a supplier cannot provide an SDS, quarantine the purchase where practicable and escalate it to the laboratory manager, procurement team or work health and safety adviser.

Organise Paper And Electronic Copies

A paper binder remains valuable during a power outage, network failure, evacuation or incident response. Keep it in an accessible location near the laboratory entrance or chemical store, but away from splash and contamination hazards. Use durable dividers arranged alphabetically, by laboratory area or by chemical risk group.

Place a contents register at the front with the chemical name, SDS page range, location and document review date. Add a “new or pending” section for products awaiting verification, but mark it clearly so staff do not mistake it for a complete SDS. Never remove the only copy of an SDS while waiting for a replacement.

Maintain an electronic version on the organisation’s approved document system or intranet. Use searchable PDF files and consistent filenames, such as manufacturer-product-concentration-review date. The GLI Quality Tool’s downloadable GLI resources can support document control, checklists and other quality activities that sit alongside the binder.

Add Risk Controls And Emergency Information

An SDS does not replace a task-specific risk assessment. For each higher-risk chemical, link the document to local controls: engineering controls, required personal protective equipment, segregation rules, spill kits, waste containers and exposure monitoring where applicable. Record who is authorised to prepare concentrated disinfectants or handle fixatives, corrosives and solvents.

Place a concise emergency contact sheet at the front of the binder. Include the laboratory manager, facility emergency number, security desk, poisons advice and local emergency services. In Australia, staff can contact the Poisons Information Centre on 13 11 26, while immediate life-threatening emergencies require 000. Confirm that these details suit the state or territory and facility.

Add a cross-reference to incident reporting, eyewash and safety shower locations, fire equipment, spill response instructions and evacuation maps. A staff member responding to a phenol splash or acid spill should not need to search several folders before finding both the SDS and the local response procedure.

Connect Chemicals With Laboratory Equipment

Chemical safety depends on the equipment used to control exposure. Check that fume cupboards, local exhaust ventilation, refrigerators, chemical cabinets and spill containment arrangements are suitable for the substances listed. Do not store incompatible chemicals together simply because they fit on one shelf.

For TB laboratories, biological safety cabinets are central to safe handling of infectious material, although they are not a substitute for chemical fume extraction when volatile or hazardous chemicals are used. Link the binder’s equipment section to inspection, certification and maintenance records. The GLI guidance on a cabinet maintenance guide can help laboratories formalise preventive maintenance for TB biosafety cabinets.

Identify chemicals that may damage cabinet surfaces, interfere with airflow or create a fire risk. Keep flammable solvents away from ignition sources, segregate acids from alkalis and cyanide-containing materials, and follow the manufacturer’s instructions for storing stains, fixatives and disinfectants.

Train Staff And Review The System

Every person who handles laboratory chemicals should know where the binder is and how to find an SDS quickly. Include this step in induction, refresher training, competency assessment and contractor orientation. Demonstrate how to interpret hazard pictograms, signal words, precautionary statements, first aid measures and spill controls.

Training should reflect the laboratory’s staffing pattern. A metropolitan service in Melbourne may have dedicated stores and safety staff, while a regional Queensland laboratory may rely on a smaller team covering several duties. The procedure should work for permanent employees, agency staff, night-shift workers, students and visiting engineers.

Review the binder during internal audits, after incidents, when a new reagent is introduced and when storage arrangements change. Track missing documents, overdue reviews and corrective actions. Staff turnover can weaken document control when experienced people leave; the GLI resource on turnover analysis offers a useful way to examine retention risks and preserve essential knowledge.

Keep The Binder Current And Usable

Assign one named role, such as the laboratory quality officer or chemical safety coordinator, to own the process. That person should maintain the master inventory, approve additions, check revisions and coordinate with procurement. A deputy should be appointed so the system continues during leave or staff changes.

Use a simple change-control record for every new, replaced or discontinued product. Record what changed, who checked the SDS, whether the risk assessment or storage arrangement needs updating and when staff were informed. Remove obsolete documents from active sections but retain them in a controlled archive if organisational policy requires a history.

Test the binder in a practical drill. Ask a staff member to locate the SDS for a corrosive stain component, identify the correct first aid action and find the spill procedure without assistance. If the search takes too long, the arrangement needs improvement. A binder succeeds when it is complete, current and usable under pressure.

Create the inventory, gather the supplier SDS documents and appoint a document owner this week. Then audit each storage area, update the paper and electronic records, brief the team and schedule a recurring review so chemical safety remains part of everyday TB laboratory quality management.