GLI GLI Quality Tool
GLI Quality Tool — Version 2.0

Creating a TB Lab SOP for Staining Quality Checks

A well-designed standard operating procedure (SOP) gives tuberculosis laboratory staff a consistent way to check whether staining reagents, technique and microscopy are performing as expected. For acid-fast bacilli (AFB) smears, control slides provide visible evidence that a staining run is suitable for reporting patient results. Learn more about How To Use Streak Plate Method Quality Controls In Tb Culture Labs 77033.

The procedure should be practical enough for a busy public pathology service and clear enough for a smaller regional or remote laboratory. It needs to explain what staff must do, what acceptable controls look like, how results are recorded and what happens when a control fails.

This is especially important where specimens travel between collection sites and testing laboratories, or where staff may work across several platforms. In Australia, a state or territory TB service might support laboratories in metropolitan Melbourne, regional Queensland, Western Australia or the Northern Territory, each with different transport times, staffing levels and equipment access.

The GLI Quality Tool supports this type of work through a phased approach to laboratory quality management. Its checklists and downloadable resources can help a laboratory connect the SOP with document control, competency assessment, equipment management, internal quality control and continual improvement.

Define Purpose Scope And Responsibilities

Begin by stating the purpose of the SOP: to verify the performance of the selected AFB staining method before patient smear results are accepted. Name the method used by the laboratory, such as Ziehl–Neelsen staining or an auramine-based fluorescent method. The scope should cover slide preparation, staining, control interpretation, documentation, troubleshooting and result release.

Specify which specimen types and work areas are included. A laboratory may process respiratory specimens, induced sputum, gastric aspirates or other material referred through a state TB network. If different staining methods are used in separate sections, write either one SOP with clearly separated workflows or a separate controlled SOP for each method.

Responsibilities should be assigned by role rather than by an individual’s name. The bench scientist may prepare and read the control slides, while the section lead reviews failures and authorises corrective action. The quality manager should monitor trends, approve revisions and confirm that records are retained. A useful supporting resource is this guide to clear job descriptions, which can help align the SOP with staff duties and competency requirements.

Choose Control Slides And Materials

The SOP should define the positive and negative control material. A positive control slide contains a known, stable preparation that demonstrates the expected acid-fast staining reaction. A negative control should contain material that does not contain acid-fast bacilli and should demonstrate a clean background without unexpected acid-fast structures.

Controls must be suitable for the method and safely managed. Laboratories should use approved or locally validated preparations, identify the source, record the preparation date and assign an expiry or review date. Store slides in a way that protects the smear from moisture, dust, fading and cross-contamination. If control slides are prepared in-house, the preparation method, verification process and storage conditions belong in a controlled document.

List all materials needed at the point of use: clean labelled slides, staining rack, reagents, water quality requirements, timers, absorbent material, immersion oil where applicable and a calibrated microscope. Include lot numbers and expiry dates for stains and decolourisers. The GLI downloadable materials can be used alongside local forms and instructions when building a complete quality documentation set.

Control slides should resemble the type of work being assessed as closely as possible. A control that is too heavily loaded may pass even when staining performance is deteriorating. A weak or unstable control may create unnecessary failures. Review control intensity periodically and replace controls when their staining characteristics, physical condition or identification become unreliable.

Write The Staining And Reading Procedure

Write the method as a sequence that a trained staff member can follow without relying on memory. Include slide identification, smear inspection, fixation, stain application, heating requirements if relevant, rinsing, decolourisation, counterstaining, drying and microscopy. State timings and critical actions precisely rather than using vague terms such as “wash well” or “decolourise sufficiently.”

Explain how control slides are positioned and processed. They should be included in the same staining run as patient slides and should pass through the same reagents, timing and handling steps. If a batch contains several racks or runs, describe whether each run needs its own controls. A control slide must not be stained separately and then used to validate a different process.

The microscopy section should define the required magnification, scanning pattern and reporting convention. For a fluorescent method, specify the instrument settings and how a positive control should appear. For Ziehl–Neelsen microscopy, describe the expected appearance of red or pink acid-fast bacilli against the counterstained background. Include a statement that patient results must not be released when the controls do not meet the acceptance criteria.

Safety instructions should be integrated into the workflow. Address infectious material, aerosols, hot equipment, staining chemicals, sharps, waste disposal and spill response. Australian laboratories should link the SOP to their local work health and safety system, including relevant state or territory requirements. A short risk note at each critical step is often more useful than a separate safety section that staff rarely consult.

Set Acceptance Criteria And Manage Failures

Acceptance criteria must be observable and specific. For example, the positive control must show the expected acid-fast staining reaction with adequate visibility, while the negative control must show no unexpected acid-fast organisms or excessive staining that could obscure interpretation. The laboratory should define who assesses the controls and whether a second reader is required for borderline findings.

A failed control invalidates the associated staining run until the cause has been assessed. The SOP should instruct staff to quarantine or flag patient results, notify the section lead, preserve the slides and record the failure. Do not simply repeat the stain and discard the original evidence. The failed controls may reveal a reagent problem, incorrect timing, poor decolourisation, contaminated water, a microscope issue or an error in slide handling.

The troubleshooting pathway should move from simple checks to deeper investigation. Confirm reagent identity, lot, expiry and preparation. Review the timer, temperature, staining sequence and microscope function. Examine whether the control slide was stored correctly and whether the smear was damaged. If the problem affects multiple runs, consider replacing reagents, checking equipment maintenance or contacting the supplier.

Define when patient specimens must be re-stained, recollected or referred. The decision should be based on the nature of the failure and the potential effect on clinical interpretation. Document the final disposition, the person who approved it and any communication with clinicians or the referring service. A clear escalation pathway is particularly important when specimens are sent from remote areas and recollection may involve significant delay.

Record Results And Review Trends

Create a control log that captures the date, staining method, operator, control identifiers, reagent lots, control findings and release decision. Add fields for failed controls, immediate action, investigation, corrective action and reviewer sign-off. Electronic records can simplify trend analysis, but a paper form may be appropriate where connectivity is unreliable.

Use the records to identify gradual deterioration rather than waiting for a dramatic failure. Repeated weak positive controls, increasing background staining or frequent failures after a new reagent lot may indicate a developing problem. Review control performance at a defined interval, such as monthly or quarterly, and include findings in the laboratory quality meeting.

The SOP should also describe document control. Record the SOP number, version, approval date, review date and authorised approvers. Remove obsolete copies from benches and shared folders. When a staining method, reagent, microscope or acceptance criterion changes, assess the impact, train affected staff and retain evidence that the revised process was verified.

Competency assessment should test the whole activity, not only the ability to recognise a positive slide. Staff should demonstrate correct preparation, staining, control interpretation, documentation and response to a failed run. Results from competency checks, internal audits and quality indicators can feed into the laboratory’s continual improvement process.

Practical Recommendations For Australian Laboratories

A control-slide SOP works best when it reflects the laboratory’s actual workload, staffing and referral arrangements. Keep the controlled procedure at the bench, use plain technical language and ensure after-hours staff can find the escalation contact. “No worries” is a useful workplace attitude, but control failures still need a documented response before results are reported.

For laboratories serving Aboriginal and Torres Strait Islander communities, quality planning should also consider access, culturally safe communication and the consequences of delayed or rejected specimens. These factors do not change the technical acceptance criteria, but they can affect collection, transport, recollection and communication with clinical teams.

The procedure should be practical for both a large metropolitan network and a small laboratory with limited staff. If a method is not performed often, add prompts for reagent checks, control-slide review and competency reassessment. If the laboratory performs high volumes, use batch identifiers and electronic flags to make failures visible quickly.

A controlled SOP turns staining quality checks using control slides into a repeatable safety barrier for TB diagnosis. Review the draft with bench staff, the quality manager and the relevant clinical or reference laboratory team, then validate it with observed runs before approval.

Place the final procedure, control log and corrective-action form where staff perform the work. Train every authorised operator, audit the process during the first review cycle and use the findings to strengthen the next version of the SOP.